Hi,

ODROID-A

Speccifications:

• Processor: Samsung Exynos4210 Cortex-A9 Dualcore 1Ghz with 1MB L2 cache
  
• Memory: 1024MB Low Power DDR2 with 64bits bus width 800Mega data rate
  
• 3D Accelerator: Mali-400 MP Core
  
• Micro-Sd slot: 8GB MicroSD(TFash)
  
• Display: 10.1inch 1366 x 768 LVDS interface with capacitive multi-touch screen
  
• Broadband: HSPA+/HSPA/UMTS/GSM/GPRS/EDGE (mini PCI Express)
  
• WiFi: 802.11 b/g/n(Broadcom BCM4329)
  
• Bluetooth: 2.1 + EDR
  
• GPS: Built-in standalone receiver (Embeddeb in 3G modem)
  
• Video: supports 1080p via HDMI cable(H.264+AAC based MP4 container format)
  
• Video Out: mini-HDMI connector with SPDIF audio
  
• Audio: Built-in speaker and microphone, standard 3.5mm headphone jack
  
• I/O: USB2.0 HS Device for ADB/Mass storage, UART/JTAG for development 30pin expandable port, 2 MicroSD Slots
  
• Power : 5V 2A Power, Battery 9000mAh(Lithium Polymer)
  
• USB: USB2.0 HS Host (Standard A type connector)
  
• Camera: Front - 1.3 Mega pixel, Rear - 3 Mega pixel autofocus
  
• Other Features: Gyroscope sensor, 3-axis accelerometer, Geo magnetic field sensor, Linear motor
  
• System Software: u-boot 2010.03, Kernel 2.6.35, Android2.3(Gingerbread)

Debug Board

• TTA20-Male Connector: Connect to I/O port of Odroid.
  
• RS232C Serial Port: Connect to Host PC RS232C Serial Port via cable.
  
• TTA20-Female Connector: External connection
  
• Mini-B USB Connector: Connect ODROID to host PC

Board detail:


More info:
MOBILE BROADBAND MODULE(F5521gw for premium connectivity):

• Modes: WCDMA/HSPA+/GSM/GPRS/EDGE
  
• Bands: WCDMA /HSPA 2100/1900/900/850MHz (Band I/II/V/VI/VIII) and GSM/ GPRS/EDGE 1900/1800/900/850MHz
  
• Speeds: HSPA Data speed D/L 21M bps U/L 5.76 Mbps and EDGE/GPRS Data speed D/L: 247 Kbps U/L: 247 Kbps
  
• GPS: Standalone, A-GPS (Internet and Network assisted)
  

Digital mobile TV

• MTV350 mobile TV RF and baseband one-chip solution for TDMB(Only for Korea domestic) from Raontech

Available from end of March
Price : US $749.00
Korean Price : 800,000원(부가세 별도)

Thanks,

Alvaro

Do you have two slots for microSD cards? Is there a picture of the back of the motherboard?
How many sensitivity points has the screen?

AMAZING!!!

I love Odroid... Thanks your the team HardKernel by do reality my dreams!!

And David, yes, i think to that have 2 ports micro-sd because is the same conexion ( we can have 64 gigas of memory ?? yeah!! )

Hardkernel,
Are you intending to supply the cad files for the plastics with the purchase of the Odroid-A.
Thanks,
Tim

Another question,
Is there any chance of getting close to Google Certification on this Odroid-A?
Cheers,
Tim

What are the viewing angles? anything like IPS screen? honeycomb? In my opinion with all the new tabs being released, the price point still seems high.

aus_dev1 wrote:Hardkernel,
Are you intending to supply the cad files for the plastics with the purchase of the Odroid-A.
Thanks,
Tim

We have .STEP files of the plastic mold tooling.
We will open it, if you need.

aus_dev1 wrote:Another question,
Is there any chance of getting close to Google Certification on this Odroid-A?
Cheers,
Tim

No, we don't have plan to get the CTS.
But, we have successfully tested GMS package of Gingerbread.
As I know, there is no developer's platform has the certification.

Insight3fl wrote:What are the viewing angles? anything like IPS screen? honeycomb? In my opinion with all the new tabs being released, the price point still seems high.

Viewing angle is slightly better than normal LCD. It is not an IPS.

Please look at this link.


Blaze™ Tablet Mobile Development Platform
http://svtronics.com/market_omap
Very similar development system cost is US$2259 without handling charge.

We believe Odroid-A is much more worthy.

Well, I was critical of your pricing for ODroid-7, because of its low-resolution screen, but I have to say that $750 for the ODroid-A sounds pretty darned reasonable. I expect to pay more for a developer kit than a mass-market item, but for ODroid-A the price is actually similar to comparable products (Xoom anyone?)

Definitely looking at getting one of these. Nice one, hardkernel!

I have looked at ODROID-A webpage
It says in the Webpage that 30pin expandable port is mounted on ODROID-A.
So, What is the 30pin expandable port? I2C?

I can't wait to get the ODROID-A!

Hi,

Update with new video and more information

Thanks,

Alvaro

yamashita_shinichi wrote:I have looked at ODROID-A webpage
It says in the Webpage that 30pin expandable port is mounted on ODROID-A.
So, What is the 30pin expandable port? I2C?

I can't wait to get the ODROID-A!

We connected GPIO/UART/ADC/USB signals to 30pin connector for hardware expansion.
I2C is also possible with bitbang on GPIO.

Thank you so so so much for your reply!

odroid wrote:

yamashita_shinichi wrote:I have looked at ODROID-A webpage
It says in the Webpage that 30pin expandable port is mounted on ODROID-A.
So, What is the 30pin expandable port? I2C?

I can't wait to get the ODROID-A!

We connected GPIO/UART/ADC/USB signals to 30pin connector for hardware expansion.
I2C is also possible with bitbang on GPIO.

odroid wrote:

aus_dev1 wrote:Hardkernel,
Are you intending to supply the cad files for the plastics with the purchase of the Odroid-A.
Thanks,
Tim

We have .STEP files of the plastic mold tooling.
We will open it, if you need.

Hello Odroid team,

Yes that would be great. We require the plastics as well.
Kindly check the email we send out. Our Korean office can respond as well if you'd like.

Kind regards,
Dennis

Hi,

We have started ODROID-A pre-order. You can purchase it from our website. The first shipment will be started from mid April. The quantity is very limited. So, the store will be closed as soon as we sell out this lot. The next shipment will be in mid May.

- Worldwide shipment : http://www.hardkernel.com/renewal_2011/shop/good_list.php?lang=en

- 한국에서의 구매 : http://www.hardkernel.com/renewal_2011/shop/good_list.php

Best regards

Do you make the HDMI available on a debug connector? Also, how about power for another device?

dennisaion wrote:

odroid wrote:

aus_dev1 wrote:Hardkernel,
Are you intending to supply the cad files for the plastics with the purchase of the Odroid-A.
Thanks,
Tim

We have .STEP files of the plastic mold tooling.
We will open it, if you need.

Hello Odroid team,

Yes that would be great. We require the plastics as well.
Kindly check the email we send out. Our Korean office can respond as well if you'd like.

Kind regards,
Dennis

We will release the 3D data file by middle of April(Just after first shipment).
Please be patient.

cloud9ine wrote:Do you make the HDMI available on a debug connector? Also, how about power for another device?

No, HDMI and debug connector are separated.
Please check below link.
http://www.hardkernel.com/renewal_2011/products/prdt_info.php?g_code=G129705660781&tab_idx=3